|Published (Last):||5 January 2014|
|PDF File Size:||1.32 Mb|
|ePub File Size:||12.78 Mb|
|Price:||Free* [*Free Regsitration Required]|
Armature plate designed to move freely is to ensure that the maximum amount of surface area comes in contact with the surface of the EM Lock. If the armature is too stiff and cannot move freely, it may not contact properly with the EM Lock.
Remark: Although an Armature plate needs to be freely of movement when installed but it should not be loose. Poor holding force. Armature and EM Lock surface is not completely contact. AC voltage input. When AC voltage from a transformer is used, a full wave brigde rectifier must be installed to convert the AC voltage to DC voltage. Low voltage Check for proper voltage at the EM Lock input. If low, determine if the correct wire gaugeis being used to prevent excessive voltage drop.
Check for proper supply load capacity. It must meet or exceed the combined current rating of all locks on the circuits. Once the plating has been removed, it cannot be restored in the field, so the EM lock will have to be periodically cleaned and coated with oil or other rust inhibitor.
If the EM Lock was installed in a heavy corrosive atmosphere, such as near to the ocean, it will eventually rust even with non abrasive cleaning. Therefore, EM Lock should be continued on a regular basis to remove the rust.
The surface of the EM Lock and the armature plate should be smooth and clean. The surfaces need to be plated and polished to ensure a good solid surface when contact each other. Double check both of the surfaces to make certain they can perform correctly. No holding force. If the voltage is low or zero, double check all the wire connections and the power supply. Need to ensure the EM lock is being correctly powered with DC voltage.
Input polarity reversed Check the voltage polarity. Terminal - is: Negative. Positive must go to red and negative to black. If the EM Lock continues operate fail, electricity need to be checked with an Ammeter. It must be powered with the correct input voltage if it draws the specified current. If reading is high or open replace the magnet coil. Magnet coil short Coil shorts or incorrect wiring will blow fuses.
You may use information on ALGATEC products and services such as data sheets, knowledge base articles, and similar materials purposely made available by ALGATEC for downloading from the Site, provided that you 1 not remove any proprietary notice language in all copies of such documents, 2 make no modifications to any such information, and 3 not make any additional representations or warranties relating to such documents.
You may not probe, scan or test the vulnerability of the Site or any network connected to the Site, nor breach the security or authentication measures on the Site or any network connected to the Site. You may not reverse look-up, trace or seek to trace any information on any other user of or visitor to the Site, or any other customer of ALGATEC, including any ALGATEC account not owned by you, to its source, or exploit the Site or any service or information made available or offered by or through the Site, in any way where the purpose is to reveal any information, including but not limited to personal identification or information, other than your own information, as provided for by the Site.
You may not forge headers or otherwise manipulate identifiers in order to disguise the origin of any message or transmittal you send to ALGATEC on or through the Site or any service offered on or through the Site.
Additionally, by using the Site, you acknowledge and agree that Internet transmissions are never completely private or secure. You understand that any message or information you send to the Site may be read or intercepted by others, even if there is a special notice that a particular transmission for example, credit card information is encrypted.
These Linked Sites are provided solely as a convenience to our visitors. You will need to make your own independent judgment regarding your interaction with these Linked Sites. The above disclaimer applies to any damages, liability or injuries caused by any failure of performance, error, omission, interruption, deletion, defect, delay in operation or transmission, computer virus, communication line failure, theft or destruction of or unauthorized access to, alteration of, or use, whether for breach of contract, tort, negligence or any other cause of action.
ALGATEC reserves the right to do any of the following, at any time, without notice: 1 to modify, suspend or terminate operation of or access to the Site, or any portion of the Site, for any reason; 2 to modify or change the Site, or any portion of the Site, and any applicable policies or terms; and 3 to interrupt the operation of the Site, or any portion of the Site, as necessary to perform routine or non-routine maintenance, error correction, or other changes.
ALGATEC reserves the right at all times to disclose any information that we deem necessary to comply with any applicable law, regulation, legal process or governmental request. ALGATEC also may disclose your information when we determine that applicable law requires or permits such disclosure, including exchanging information with other companies and organizations for fraud protection purposes.
You agree that ALGATEC may, in its sole discretion and without prior notice, terminate your access to the Site, for cause, which includes but is not limited to 1 requests by law enforcement or other government agencies, 2 a request by you self-initiated account deletions , 3 discontinuance or material modification of the Site or any service offered on or through the Site, or 4 unexpected technical issues or problems.
Users may be asked for, as appropriate, name, company information, country of origin, email address, mailing address and phone number. Users may, however, visit our Website anonymously.
We will collect personal identification information from Users only if they voluntarily submit such information to us. Users can always refuse to supply personally identification information, except that it may prevent them from engaging in certain website related activities, such as downloading technical documentation like data sheet, installation guide, and other product related documents. Non-personal identification information We may collect non-personal identification information about Users whenever they interact with our Website.
Non-personal identification information may include the browser name, the type of computer and technical information about Users means of connection to our Website, such as the operation system and the Internet service providers utilized and other similar information.
We do not collect PII from you unless you elect to provide it to us. This data is used to manage and improve your experience on the Website and for any other business activities. How we protect your information ALGATEC uses commercially reasonable administrative, technical, personal and physical measures to safeguard PII in its possession against loss, theft and unauthorized use, disclosure or modification. However, no security measures are perfect or impenetrable. We cannot control the actions of other users with whom you elect to share your PII.
We cannot guarantee that only authorized persons will view your PII. We cannot ensure that information you share on our Website will not become publicly available. We are not responsible for third party circumvention of any privacy settings or security measures on our Website.
You can reduce these risks by using common sense security practices such as choosing a strong password, using different passwords for different services, and using up to date antivirus software. Sharing your personal information We do not sell, trade or rent Users personal identification information to others. We may share generic aggregated demographic information not linked to any personal identification information regarding visitors and users with our business partners, trusted affiliates and advertisers for the purposes outlined above.
We may use third party service providers to help us operate our business and the Website or administer activities on our behalf, such as sending out newsletter or surveys. We may share your information with these third parties for those limited purposes provided that you have given us your permission. We encourage you to frequently check this page for any changes to stay informed about how we are helping to protect the personal information we collect.
This Warranty is limited to the original purchaser only. This warranty shall not apply if the Product has been subject to misuse, accident, negligence, abuse, customer changes, improper installation, or improper or abnormal or operating conditions, or if the product has been lost or damaged in transit.
This Warranty is expressly in lieu of all other warranties, expressed or implied, and of all other obligations or liabilities on the part of ALGATEC of any kind or character, including without limiting the generality of the foregoing, implied warranties of merchantability and fitness for use and liabilities for alleged representations or negligence. We shall in no event be liable for any direct, indirect, economic, pecuniary or consequential damages.
Shortages An official written claim for shortages must be made within 10 days after receipt of the order. All returns must be issued a return authorization number prior to sending back to our facility.
Returns can be done immediately or periodically depending on the urgency. They will be addressed promptly. Warranty information is available upon request for individual product. Returned Goods Any defects or errors for which we are responsible for will be promptly rectified. Returned goods will not be accepted without prior approval and a return authorization number, which must appear on all documentation relating to the returned merchandise. The original invoice number and purchase order number is required on all returns.
algatec em lock